Jlg 4017 Platform Operator Manual Manual de usuario

Operator & SafetyManualKeep this manual with machine at all times.Platformfor3513, 4013& 401731200029RevisedFebruary 27, 2006

Section 1 - General Safety Practices1-2312000291.3 OPERATION SAFETYElectrical Hazards• This machine is not insulated and does not provide protection f

Section 1 - General Safety Practices1-331200029Tip Over Hazard• DO NOT exceed rated lift capacity. Distribute loads evenly on platform floor.• Be sure

Section 1 - General Safety Practices1-431200029Load Falling Hazard• Never suspend load from platform or supports.• DO NOT carry materials directly on

Section 1 - General Safety Practices1-531200029Lifting Personnel• USE ONLY a JLG manufactured personnel work platform.• DO NOT drive machine from cab

Section 1 - General Safety Practices1-631200029Pinch Points and Crush HazardsStay clear of pinch points and rotating parts on the telehandler.• Stay c

Section 1 - General Safety Practices1-731200029• Keep arms and hands clear of attachment tilt cylinder.• During operation, keep all body parts inside

Section 1 - General Safety Practices1-831200029Fall Hazard• During operation, occupants in the platform must wear a full body harness with alanyard at

Section 1 - General Safety Practices1-931200029Chemical HazardsExhaust Fumes• DO NOT operate machine in an enclosed area without proper ventilation.•

Section 1 - General Safety Practices1-1031200029This Page Intentionally Left Blank

Section 2 - Pre-Operation and Controls2-131200029SECTION 2 - PRE-OPERATION AND CONTROLS2.1 PRE-OPERATION CHECKS & INSPECTIONNote: Complete all re

Section 2 - Pre-Operation and Controls2-231200029Begin your platform walk-around inspection at item 1, as noted below. Continue toyour right (counterc

Section 2 - Pre-Operation and Controls2-3312000292.2 SAFETY DECALSEnsure all DANGER, WARNING, CAUTION and instructional decals and propercapacity ch

Section 2 - Pre-Operation and Controls2-431200029OZ178017066041706604A17066041706604A170660417066031706602A17066021706604A

Section 2 - Pre-Operation and Controls2-531200029OZ1790170150917015091704277 B1704277P/NAERIAL PLATFORMS/NMODELProducer:Industrieterrein Oude Bunders

Section 2 - Pre-Operation and Controls2-6312000292.3 CONTROLS1. Emergency Stop Button: Push in to shut off power to platform controls and stop engine.

Section 2 - Pre-Operation and Controls2-731200029Ignition•Position 0 - Engine off•Position IGN - Voltage is available for all electrical functions.•Po

Section 2 - Pre-Operation and Controls2-831200029JoystickThe joystick (1) controls the boom and attachment functions.Note: Buttons (5) & (6) are

Section 2 - Pre-Operation and Controls2-931200029Platform Functions• Platform tilt is enabled by button (2) and controlled by the rocker switch (3). P

Section 2 - Pre-Operation and Controls2-1031200029Indicator Panels1. Engine Temperature: Illuminates red when engine temperature is high.2. Battery Ch

Section 2 - Pre-Operation and Controls2-11312000299. System Distress Indicator:a. Flashes yellow and buzzer sounds intermittently when pressure is low

Revision Loga31200029Revision LogREVISION LOGOctober 3, 2005 - A - Original Issue of ManualFebruary 27, 2006 - B - Added 4017 information.

Section 2 - Pre-Operation and Controls2-12312000292.4 PLATFORM GATEKeep gate clean and unobstructed.• Pull the black hook (1) away from the gate and p

Section 2 - Pre-Operation and Controls2-13312000292.5 LANYARD ANCHORAGE POINTS• Attach lanyard to one of the lanyard anchorage points (2).• Only attac

Section 2 - Pre-Operation and Controls2-1431200029This Page Intentionally Left Blank

Section 3 - Operation3-131200029SECTION 3 - OPERATION3.1 WARM-UP AND OPERATIONAL CHECKSThis section outlines the checks to be performed at the beginni

Section 3 - Operation3-2312000293.2 ENGINEStarting the EngineThis machine can be operated in temperatures of -20°C to 40°C (0°F to 104°F).Consult JLG

Section 3 - Operation3-331200029Normal Engine Operation• Observe indicator panels frequently to be sure all engine systems are functioningproperly.• B

Section 3 - Operation3-4312000293.3 PLATFORM OPERATION• After engine start-up from the platform is successful, activate the footswitch toenable the pl

Section 3 - Operation3-5312000293.4 LOADING AND SECURING FOR TRANSPORT1. To move/load the platform when detached from telehandler, use fork slots loca

Section 3 - Operation3-631200029This Page Intentionally Left Blank

Section 4 - Platform4-131200029SECTION 4 - PLATFORM4.1 APPROVED PLATFORMSTo determine if platform is approved for use on the specific telehandler you

Read This Firstb31200029Read This FirstThis manual is a very important tool! Keep it with the machine at all times.The purpose of this manual is to pr

Section 4 - Platform4-2312000294.3 TELEHANDLER/PLATFORM CAPACITYPrior to installing the platform verify it is approved (see page 4-1) and thetelehandl

Section 4 - Platform4-3312000294.4 PLATFORM INSTALLATIONVerify the platform is properly installed.Refer to the Operator & Safety Manual supplied w

Section 4 - Platform4-431200029Mechanical Quick-Switch DeviceAttachment pin engaged in platform pin recess andlock pin inserted and secured with retai

Section 5 - Emergency Procedures5-131200029SECTION 5 - EMERGENCY PROCEDURES5.1 EMERGENCY OPERATIONOperator Unable to Control MachineIf the platform op

Section 5 - Emergency Procedures5-2312000295.2 EMERGENCY LOWERING OF BOOMIn case of an emergency, engine or hydraulic failure an emergency recovery sy

Section 5 - Emergency Procedures5-3312000295.3 INCIDENT NOTIFICATIONJLG Industries, Inc. must be notified immediately of any incident involving a JLGp

Section 5 - Emergency Procedures5-431200029This Page Intentionally Left Blank

Section 6 - Lubrication & Maintenance6-131200029SECTION 6 - LUBRICATION & MAINTENANCE6.1 INTRODUCTIONService the product in accordance with Se

Section 6 - Lubrication & Maintenance6-2312000296.3 SERVICE & MAINTENANCE SCHEDULES8 Hour Maintenance ScheduleOZ1572Check FuelLevelCheckBatter

Section 6 - Lubrication & Maintenance6-3312000296.4 OPERATOR MAINTENANCE INSTRUCTIONSFuel SystemA. Fuel Level Check1. Check fuel gauge (1) located

Read This Firstc31200029This product must comply with all safety related bulletins. Contact JLG Industries,Inc. or the local authorized JLG representa

Section 6 - Lubrication & Maintenance6-431200029TiresA. Tire Air Pressure Check1. Perform “Shut-Down Procedure” on page 3-3.2. Remove valve stem c

Section 6 - Lubrication & Maintenance6-531200029BatteryA. Battery Check1. Perform “Shut-Down Procedure” on page 3-3.2. Open the engine cover.3. We

Section 6 - Lubrication & Maintenance6-631200029This Page Intentionally Left Blank

Section 7 - Additional Checks7-131200029SECTION 7 - ADDITIONAL CHECKS7.1 EMERGENCY RECOVERY SYSTEM TESTThe Emergency Recovery System (ERS) is availabl

Section 7 - Additional Checks7-2312000297.2 LIMITED BOOM EXTENSION SWITCH TESTAustralian machines are equipped with a switch (1) on the boom to limit

Section 8 - Specifications8-131200029SECTION 8 - SPECIFICATIONS8.1 PRODUCT SPECIFICATIONSFor telehandler specifications refer to the Operator & Sa

Section 8 - Specifications8-231200029This Page Intentionally Left Blank

Index131200029AAdditional Checks... 7-1Approved Platforms... 4-1BBattery Check...

Index231200029TTip Over Hazard ... 1-3Tire Pressure... 6-4VVibration ...

Inspection, Maintenance & Repair Log131200129Serial Number ______________________________Date CommentsInspection, Maintenance & Repair Log

Read This Firstd31200029This Page Intentionally Left Blank

Inspection, Maintenance & Repair Log231200129Date Comments

JLG Industries, Inc.TRANSFER OF OWNERSHIPTo: JLG, Gradall, Lull and SkyTrak product owner:If you now own but ARE NOT the original purchaser of the pro

JLG Worldwide LocationsCorporate OfficeJLG Industries, Inc.1 JLG DriveMcConnellsburg PA. 17233-9533USAPhone: (717) 485-5161Customer Support Toll Free:

Table of Contentsi31200029TABLE OF CONTENTSRevision LogRead This FirstOperator Qualifications ... b

Table of Contentsii 31200029Section 4 - Platform4.1 Approved Platforms..... 4-14.2 Unapproved

Section 1 - General Safety Practices1-131200029SECTION 1 - GENERAL SAFETY PRACTICES1.1 GENERAL PRECAUTIONS• DO NOT use the machine with platform attac